the Amplifier Research 3000TP12G18 TWT Amplifier : The Amplifier Research 3000TP12G18 is a self contained, forced air cooled, broadband traveling wave tube (TWT) microwave amplifier designed for pulse applications at low to moderate duty factors where instantaneous bandwidth and high gain are required. A reliable TWT provides a conservative 3000 watts minimum peak RF pulse power at the amplifier output connector. Stated power specifications are at the fundamental frequency. The amplifier’s front panel digital display shows forward and reflected average power output or forward and reflected peak power, plus extensive system status information accessed through a series of menus via soft keys. Status indicators include power on, warm-up, standby, operate, faults, excess average or peak reflected power warning and remote. Standard features include a built-in IEEE-488 (GPIB) interface, 0dBm input, TTL Gating, VSWR protection, gain control, RF output sample port, auto sleep, plus monitoring of TWT helix cur, cathode voltage, collector voltage, heater cur, heater voltage, baseplate temperature and cabinet temperature. Modular design of the power supply and RF components allow for easy access and repair. Use of switching mode power supplies results in significant weight reduction. Housed in a stylish contemporary cabinet, the amplifier provides readily available pulsed RF power for a variety of applications in Test and Measurement, (including EMC RF pulse susceptibility testing), Industrial and University Research and Development, and Service applications. AR also offers a broad range of amplifiers for CW (Continuous Wave) applications. See Amplifier Research Configurations for alternative prime power, packaging, and special features.  Functions and Specifications of the Amplifier Research 3000TP12G18 TWT Amplifier Includes: POWER (Fundamental), Peak Pulse, @ OutputNominal: 3800 wattsMinimum: 3000 watts FLATNESS: ±10 dB maximum FREQUENCY RESPONSE: 12–18 GHz INPUT FOR RATED OUTPUT: 1.0 milliwatt maximum GAIN (at maximum setting): 65 dB minimum GAIN ADJUSTMENT (continuous range): 35 dB minimum INPUT IMPEDANCE: 50 ohms, VSWR 2.5:1 maximum OUTPUT IMPEDANCE: 50 ohms, VSWR 2.5:1 typical MISMATCH TOLERANCE: Output pulse width foldback protection atpeak reflected power exceeding 1000 watts. Will operatewithout damage with any magnitude and phase of source andload impedance. May oscillate with unshielded open due tocoupling to input. Should not be tested with connector off.See S2M special option, if applicable. PULSE CAPABILITYPulse Width: 0.07–50 microseconds.Pulse Rate (PRF): 100 kHz maximumDuty Cycle: 4% maximum.RF Rise and Fall: 30 ns max (10% to 90%).Delay: 300 ns maximum from pulse input to RF 90%Pulse Width Distortion: ±30 ns maximum (50% points of output pulse width compared to 50% points of input pulse width)Pulse Off Isolation: 80 dB minimum, 90 dB typicalPulse Input: TTL level, 50 ohm nominal termination NOISE POWER DENSITY:(pulse on) Minus 55 dBm/Hz (maximum);Minus 65 dBm/Hz (typical) (pulse off)Minus 140 dBm/Hz (typical) HARMONIC DISTORTION: Minus 8 dBc maximum PRIMARY POWER: See Model Configurations CONNECTORSRF input: Type N female on rear panelRF output: Type WR62 waveguide flange on rear panelRF output forward sample port: Type N female on rear panelPulse input: Type BNC female on rear panelGPIB: IEEE-488 female on rear panelInterlock: DB-15 female on rear panel COOLING: Forced air (self contained fans), air entry and exit in rear. SIZE: 50.3 x 26 x 69cm (19.8 x 10 x 27in) WEIGHT: 52 kg (115 lbs)     

• Amplifier Research 3000TP12G18 - Datasheet (57 Ko)